Japan Amusement Machine and Marketing Association
Template:Short description Template:Use dmy dates Template:More citations needed Template:Infobox organization
The Template:Nihongo (formerly the Template:Nihongo, abbreviated JAMMA) is a Japanese trade association headquartered in Tokyo.
JAMMA is run by representatives from various arcade video game manufacturers, including Bandai Namco, Sega, Taito, Koei Tecmo, Capcom, and Konami among others. Nintendo was also a member of the organization until its departure on February 28, 1989.<ref>Template:Cite web</ref> Nihon Bussan left in 1992 over content issues in their mahjong games.<ref name="nichibutsu1992">[麻雀ゲームの審査に不満を示した日本物産の退会で議論」, Game Machine issue 420 (1992), p. 3 (Japanese)]</ref>
The corporation was renamed on 1 April 2012 after they merged with the Nihon Shopping Center Amusement Park Operator's Association (NSA) and the Japan Amusement Park Equipment Association (JAPEA).
Before 2012, JAMMA had been organizing an annual trade fair called the Amusement Machine Show for many years. In 2013, they began collaborating with the Amusement Machine Operators' Union (AOU), who had their own trade show, to promote a new event: the Japan Amusement Expo.
Arcade machine standards
Controllers
JAMMA is the namesake of a widely used wiring standard<ref>Template:Cite web</ref> for arcade games. An arcade cabinet wired to JAMMA's specification can accept a motherboard for any JAMMA-compatible game.<ref>Template:Cite magazine</ref> JAMMA introduced the standard in 1985; by the 1990s, most new arcade games were built to JAMMA specifications. As the majority of arcade games were designed in Japan at this time, JAMMA became the de facto standard internationally.
Before the JAMMA standard, most arcade PCBs, wiring harnesses, and power supplies were custom-built. When an old game became unprofitable, many arcade operators would rewire the cabinet and update the artwork in order to put different games in the cabinets. Reusing old cabinets made a lot of sense, and it was realized that the cabinets were a different market from the games themselves. The JAMMA standard allowed plug-and-play cabinets to be created (reducing the cost to arcade operators) where an unprofitable game could be replaced with another game by a simple swap of the game's PCB. This resulted in most arcade games in Japan (outside racing and gun shooting games that required deluxe cabinets) to be sold as conversion kits consisting of nothing more than a PCB, play instructions and an operator's manual.Template:Citation needed
The JAMMA standard uses a 56-pin edge connector on the board, with inputs and outputs common to most video games. These include power inputs (5 volts for the game and 12 volts for sound); inputs for two joysticks, each with three action buttons and one start button; analog RGB video output with negative composite sync; single-speaker sound output; and inputs for coin, service, test, and tilt.<ref>Template:Cite web</ref><ref>Template:Cite web</ref>
The JAMMA connector has a .156" pin spacing edge connector (male on the game board)<ref>Template:Cite web</ref> with other specifications based on number of pins.<ref>Template:Cite web</ref>
20 pin,<ref>Template:Cite web</ref> 36 pin,<ref>Template:Cite web</ref> 44 pin,<ref>Template:Cite web</ref> 56 pin<ref>Template:Cite web</ref> and 72 pin<ref>Template:Cite web</ref> connectors are available where the 56 pin JAMMA connector pinouts values<ref>Template:Cite web</ref> are shown in the reference table and other game boards connectors may have different pinout values.<ref>Template:Cite web</ref>
The connector circuitry of some later games, such as Street Fighter II: The World Warrior (1991) and X-Men (1992), implement extra buttons, different controller types, or support more players by adding extra connectors—or even by utilizing dormant JAMMA pins. Circuitry designs that overstep the JAMMA specification in this way are unofficially called JAMMA+.<ref>Template:Cite web</ref>
Video
The JAMMA Video Standard (JAMMA VIDEO規格, JVS) is a newer JAMMA connector standard. The standard specifies a communication protocol based on RS-485 and physical interfaces for peripheral devices using commonly-available USB connectors and cables. JVS is incompatible with USB devices because it does not use the USB signaling standard and protocol.
Per the first edition of the JVS, published in 1996,<ref name=jguide>Template:Cite web</ref> peripheral devices connect to a dedicated I/O board.<ref>JVS-PAC Introduction</ref> The main board connects to the I/O board via a USB Type-A to USB Type-B interface cable, and peripherals connect to the I/O board via USB-A connectors.
JAMMA published the second edition of the JVS on 17 July 1997, and the third edition on 31 May 2000. The third edition adds support for ASCII and Shift-JIS output; device drivers for secondary and tertiary input devices; a device driver for a mahjong controller; and recommended values for SYNC-code timing.
Similar technologies
Other manufacturers use similar edge connectors such as Tektronix for the TM50X, TM500X,<ref>Template:Cite web</ref><ref>Template:Cite web</ref><ref>Template:Cite web</ref> 5000 and 7000<ref>Template:Cite web</ref><ref>Template:Cite web</ref> system mainframe equipment.<ref>Template:Cite web</ref><ref>Template:Cite web</ref><ref>Template:Cite web</ref>
Connectors with similar designs have been used for different systems circuitry interfaces with 22 pins such as the Tektronix SC-503 extender, 26 pins 58900A Extender, 48 pins 5080-2843A Extender, 72 pins J-2306-01 Extender Board and others.
Some systems circuitry interfaces use special adapters that have been custom-made using the JAMMA connectors, such as with the Tektronix TM500/5000/7000 series extension cable adapters.<ref>Template:Cite web</ref><ref>Template:Cite web</ref><ref>Template:Cite web</ref>
These different systems can be custom-built based on user requirements, where even basic guides have been created to assist users in the making of such adapters.<ref>Template:Cite web</ref><ref>Template:Cite web</ref>
See also
- Expansion card
- IEEE-488 (IEEE-488 GPIB or HPIB connectors)
- Micro ribbon connector
- Registered jack 21 (RJ21 Telco 50)